Making Game: How to use external display as default

Original Source Link

When I use my external monitor with my laptop, the external monitor begins to display when the OS starts to load, unlike the internal monitor in the laptop, which begins to display from the beginning, including the OEM Logo and bios.

It is the same when I connect the monitor to my old laptop or my friend’s laptop.

It doesn’t matter at first, but recently I go an embedded machine, I want to use the external monitor to setup OS, although the monitor detected signal, but do not display anything.

The embed machine is functional, because it worked when I use my friend’s monitor.

So how to make a external monitor work as the default monitor of a computer, so it can display when booting up like desktop?

Or there are differences that some monitors can and some can’t?

I think this has to do with the way BIOS reads your displays and may or may not be posible, for instance in my MultiMonitor setup, I have the HDMI output setup as default, and works fine once the OS loads up, but during bootup, the default is always the VGA monitor. You can check if your BIOS settings has any such feature.

Similarly your embedded system needs to be able to display on your external Monitor without OS driver support..

edit: this page seems to tackle the same issue.

Tagged : / /

Linux HowTo: How to use external display as default

Original Source Link

When I use my external monitor with my laptop, the external monitor begins to display when the OS starts to load, unlike the internal monitor in the laptop, which begins to display from the beginning, including the OEM Logo and bios.

It is the same when I connect the monitor to my old laptop or my friend’s laptop.

It doesn’t matter at first, but recently I go an embedded machine, I want to use the external monitor to setup OS, although the monitor detected signal, but do not display anything.

The embed machine is functional, because it worked when I use my friend’s monitor.

So how to make a external monitor work as the default monitor of a computer, so it can display when booting up like desktop?

Or there are differences that some monitors can and some can’t?

I think this has to do with the way BIOS reads your displays and may or may not be posible, for instance in my MultiMonitor setup, I have the HDMI output setup as default, and works fine once the OS loads up, but during bootup, the default is always the VGA monitor. You can check if your BIOS settings has any such feature.

Similarly your embedded system needs to be able to display on your external Monitor without OS driver support..

edit: this page seems to tackle the same issue.

Tagged : / /

Linux HowTo: How to scale down secondary display in pop os 20.04 LTS?

Original Source Link

Machine- Asus Fx503vd Laptop

OS- pop os 20.04 lts

Inbuilt display: 1920*1080(16:9)

Secondary display:1440*900(16:10)

My Secondary display is enlarged by default around 125% and there is no option in settings to handle this situation. So how can I scale down my secondary display a little?

This happens if I use youtube in full-screen mode but everything works fine in primary display

Youtube At Full Screen

Tagged : / /

Linux HowTo: My notebook’s display frequently turns off for a moment? With external screen, it’s even more frequent

Original Source Link

Currently I use my notebook without an external display, and the following happens:

  • a few weeks ago it started to lose signal occasionally.

  • And it’s a really short period, because after my screen goes black, it instantly “starts to come back”.

I tried using this display via HDMI: https://www.acer.com/ac/en/GB/content/model/UM.HV0EE.P01

And it seems that it’s much more regular on the 2K display, than on my 1080p integrated screen.

Here is what I’ve experienced with an external display:

  • Another has just happened, and it was simultanous with the refrigerator’s fans turning off. Later, it happened again when the fridgerator turned its fans on. I will watch out whether there are more “suspicous” things or not.

  • Now for 3 minutes, it happened like every 45 seconds. And I didn’t notice any electric change in the room.

  • I pulled out the charger from the notebook, to see if there is any difference, and after a few minutes, it began to turn off like every 4 seconds, sometimes they even overlapped, causing long black screens.

  • It also seemed like when I moved the mouse, it got black. I pulled out the mouse, and the frequent black screen suddenly stopped.

  • Then I put it back after half a minute, and it’s still not that frequent, but there are black screens again.

The problems seem to be power-oriented:

  • The fact that turning electrical appliances on/off in the house causes
    problems may mean that the electricity in your house is not well isolated
    and some appliances cause strong electrical surges, which is quite dangerous.
    In that case the computer needs to be protected with a UPS
    or at least with a surge protector.

  • The fact that the computer cannot work without the charger may mean that the
    battery is nearly dead.

  • As this happens very rarely outside of your house, but still happens,
    and that connecting devices also has a negative effect,
    might mean that your Power Supply Unit (PSU) is weakening.

If the computer is new, use the warranty to have it replaced.
A repair-shop will have the tools and replacement parts to better analyze the
problem. However, if the computer is quite old, ask for estimates for the
repairs to see if the investment is worthwhile.

Tagged : / /

Making Game: Laptop lid closed and screen disabled once system is up

Original Source Link

I have laptop and external monitor. I set up in power settings for lid to Do nothing when is closed, besides i also set up all options to Do Nothing therefore when i close the lid when system is running and open lid again my laptop’s screen turn on as well. No issue.

Nevertheless when laptop lid is closed and i run Windows 10 system then when i open laptop’s lid once system is up – laptop screen is not turning on. I even do not see that screen in Display settings. How to make laptop screen enable once i open lid in this particural case?

My setup:

> HP 8760W + docking station (video: NVIDIA)
> LG 34 (external monitor)

Tagged : / /

Linux HowTo: View PC graphics output without monitor

Original Source Link

I recently inherited an older PC running win7 and I wanted to see if it still works, the issue is I don’t have an VGA monitor and VGA is all the computer supports, so at the moment, there is no way for me to see what is going on at the moment, so I was wondering if there is any software available that I can use on my android phone as a monitor via USB where I do not need to install any additional software on the older device. If anyone has any suggestions as to how I might be able to view the device’s output, that would be brilliant. Thanks in advance.

It’s VGA, not RGB – you’ll need some flavour of software for remote access. You can’t just plug a phone into a PC over USB and get it to do anything, let alone be a monitor by itself.

Now the solution you need is something that converts VGA to a HDMI or DP – these are commodity items with a bunch of options. You can then plug it into a modern monitor. Presumably you can then set up some remote access software to run it over wifi.

Tagged : / / /

Making Game: View PC graphics output without monitor

Original Source Link

I recently inherited an older PC running win7 and I wanted to see if it still works, the issue is I don’t have an VGA monitor and VGA is all the computer supports, so at the moment, there is no way for me to see what is going on at the moment, so I was wondering if there is any software available that I can use on my android phone as a monitor via USB where I do not need to install any additional software on the older device. If anyone has any suggestions as to how I might be able to view the device’s output, that would be brilliant. Thanks in advance.

It’s VGA, not RGB – you’ll need some flavour of software for remote access. You can’t just plug a phone into a PC over USB and get it to do anything, let alone be a monitor by itself.

Now the solution you need is something that converts VGA to a HDMI or DP – these are commodity items with a bunch of options. You can then plug it into a modern monitor. Presumably you can then set up some remote access software to run it over wifi.

Tagged : / / /

Making Game: How to use an iMac G3 as an external monitor?

Original Source Link

I’ve read that the tray-loading iMac G3’s CRT display is connected to the circuit board with a simple plug. Can I unplug the CRT from the computer part and use the iMac G3 as an external monitor? How can I do this? I couldn’t find any good tutorials on YouTube or anywhere else. Thanks in advance!

Tagged : / / / /

Making Game: Getting ”no input signal” in external monitor

Original Source Link

I have Dell XPS 13 which is running Ubuntu 20.04. I had an old monitor, which had only VGA port. And I had a Thunderbolt adapter, which had only HDMI port. So I connected both of them using a VGA to HDMI adapter. In the display settings, it is shown as the maximum resolution of the external monitor is 1920×1080. But when I select that, I get “No input Signal” error in the monitor. What should I do to get that resolution, or isn’t that possible?

Tagged : / / / /

Linux HowTo: External monitor turning black intermittently

Original Source Link

I have installed an external monitor (Dell ST2220L, 21.5 inch) on my laptop (Sony Vaio). I am using a DVI-D cable for connection. Since the laptop does not have a DVI-D port, I have connected a DVI-D to HDMI connector on the laptop end and inserted the cable in HDMI port of the laptop..

I have switched off the laptop display and adjusted the screen resolution on the Dell external monitor to 1920 x 1080 and adjusted colors for the Windows 7 and brightness and contrast from the monitor.

The problem is the monitor turns of blank intermittently for 1-2 seconds and turns on again at random interval. What could be the reason for this and how to get rid of this problem?

This seems to be a connectivity issue. Try and wiggle the adapter, and all the connections while powered, and see if you can make the problem appear. Don’t forget to test the connection at the display too.

I believe it’s most likely a bug in the generic Windows display driver. It’s possible you can solve this with a driver from Dell for your display.

I’ve struggled with exactly that same behavior in one of my monitors, where it randomly goes dark for a couple seconds, then comes back on. The interval between could hours or it could seconds (almost constant flickering.)

In my case, it’s two Dell 2405FPW panels side-by-side on my desktop and the problem only presented on my left monitor. Web searches at the time confirmed this a common problem, but seen only on the then-new Windows release I was running and could be traced to Dell having dropped support and not releasing a driver. The random behavior was because I was using the default driver. It drove me nuts for years (but I was too cheap to buy new panels that were supported.) The problem finally (fingers crossed) appears to have gone away a couple months ago with an Nvidia update for my graphics card.

In your case, I don’t see others reporting the same behavior with your model and it looks like Dell still supports your monitor. But the behavior you’re seeing is exactly what I saw from the default driver. This is why I suspect it may be as simple as downloading the proper driver from Dell.

Good luck. I hope this helps.

I believe it is an HDMI issue as I am having the same problem with a new Vizio 50-inch LED TV. When using HDMI to watch cable tv or Blu-ray discs I get intermittent “no signal” displays where both video and audio disappear for a couple of seconds and then come back. Using component connections I don’t have that problem. I don’t like using component since the picture quality is not as good, but I can’t find a better solution for the time being.

I had the same problem with a Dell U2515H screen that turned blank for a second or two now and then. Had the newest drivers installed for both the graphics card and the monitor.

Was able to solve it by disable “DP 1.2” (had enable it previously to allow daisy chain of two monitors).

There are many reasons why a monitor keeps turning off, resulting in
a blank display. The best way to resolve this problem is through
process of elimination; as such, I will go through the list of things
you can do to help determine why the monitor keeps going black or
turning off sporadically.

Simply put: both DVI and HDMI are digital signals; if the signal is
too weak, the monitor won’t sync to the computer, resulting in a blank
screen. If the cable run is too long, or of the signal has been split
(using a non-powered DVI or HDMI splitter), this can cause the monitor
to go black because the signal isn’t strong enough.

Based on my experience, some HDMI cables will simply stop syncing
properly after a while, even though they worked fine previously, and
even though the same cable works fine on another device. Sometimes,
HDMI cables won’t work properly if there has been a recent hardware
configuration change. For example, you may have purchased a stereo
receiver and ran the cable through the receiver instead of directly
through the monitor. In this case, you can bypass the splitter or
receiver and see if that makes any difference.

https://www.infopackets.com/news/9589/how-fix-monitor-keeps-going-black-turning

I had this exact same problem with a Surface Pro 4, Monoprice monitor MP-28UHDSS. Seemed to start happening after the Windows 2018 May Update. I tried various suggestions, none worked for me until I went to Advanced Display Settings, Display Adapter Properties, and found that the screen refresh rate was set at 59Hz. No idea where that came from. I changed to 30Hz, and problem is definitely gone.

For some strange reason whenever my phone is near the usb-c adapter thing the external monitor turns off. At first my external monitor wouldn’t go on because my phone was near the adapter when i moved my phone away it turned on and there was no turning black intermittently ever again.

This is going to sound crazy, but I have solved this and other external display issues in Windows 10 by simply logging in as an administrator on the computer. Then I can log out and back in as my regular user, and the issue is gone!

I usually run Windows as non-admin, and it seems Windows wants to “do things” with regards to the monitor that it needs administrator rights to do. Weird that I get no notification whatsoever about this.

(Edit 1: It seems like I have to always remain logged in as an administrator in the background, and switch to my regular user, for the issue not to appear again.)

(Edit 2: Like I have read on other places, these kinds of fixes usually only work for a short while, so the problem was NOT solved.)

(Edit 3: The problem was solved when I switched monitor. It seems my DELL UltraSharp 24 something was faulty or incompatible somehow. A newer DELL UltraSharp 27 and a Samsung 27 works perfectly now.)

So here’s something interesting to add to this older discussion…I currently use a pair of monitors (mismatched, an Acer V276HL, connected via DVI-D, and a ViewSonic VX2753MH-LED.

The ViewSonic died a couple of years ago. The input connectors and power connector failed one by one, and I eventually ended up buying a new driver board from ViewSonic and replacing it this past November.

As of last week, the monitor began shutting off, and coming back on. I don’t think it was a signal loss: the display would completely power off and the ViewSonic logo would show after it restarted.

During this time it was connected via HDMI, to my PC.

I wanted to test out whether or not it was the signal, etc., so I switched it to the other DVI port, with a DVI-I to VGA converter, and ran that into the VGA connection on the back of the monitor (it has two HDMI ports as well).

I assumed it would also turn off and on, my suspicion was that the replacement board was rapidly going bad. But now that I have it connected to a standard 15-pin VGA input, it’s been rock solid for the last 48 hours.

So, you might try a different cable method even if the quality isn’t exactly what you’d prefer, and see if it keeps doing it.

Current fluctuation at mains supply can cause HDMI monitor to momentarily black-out, such as a fridge compressor switching on and off.

spurious voltages on the hdmi cable and induced voltages can cause something like a capacitance to build and cause issues…

Turn off PC, unplug monitor hdmi at both monitor and pc, UNPLUG THE PC. Let the power supply drain (wait a few minutes). Unplug the monitor power.

Now, connect monitor and pc hdmi. Plug in monitor and plug in pc.. if all goes well the spurious voltage that was there will disappear.

If it comes back – check you are not running power cables un-shielded next to your monitor cables or other cables going to or from pc. Just give them some room… cheap cables are highly susceptible to cross em interference.

Try using another, better quality preferable, hdmi cable also. Make sure there’s no dust on the pins or components. If you have access into the PC – carefully follow manufacturer recommended cleaning (gently air dusting to remove dirt building up on main boards and graphics cards or other components – especially in the power supply and graphics connection points. DO THIS WHILE IT IS UNPLUGGED!!!! If you don’t know what you’re doing – call a friend that does.

If all else fails – check your power supply voltages and make sure they are all within normal tolerances. Some monitors are easily damaged by unbalanced grounds on the hdmi and main power. There may be dangerous reverse potential on the neutral or ground lines as a result of a failed diode or something.. can’t tell you all the many ways I have seen electronics lose their magic smoke but there are many possible physical component issues possible.

By far the most likely is that the cable is bad or there is some random spurious voltage that has been induced on the line somewhere. HDMI has power on it and if there is a connection that is not solid or any standing waives from a kink in the line or otherwise it can cause issues… just replace and be sure to keep the ends clean and dirt free. Things happen even when they are not moved or touched.. try to troubleshoot and good luck!

Of course – if the signal is weak and you’re running too far it can cause issues too.. again – a better cable with lower impedance can help there too. Always check sync freq and normal driver updates too. That’s a no-brainer… keep your drivers up to date. There’s usually a reason a manufacturer releases a driver update when they take the time to do so. I use a couple tools from IOBIT to keep my family pc’s up to date and running smooth. Love the one-click button options – super easy to use – Advanced System Care Pro. There is a free option too – but the pro is pretty cheap and well worth it – and can be installed on several PC’s if I am not mistaken…

Let us know how it works out!

Tagged : / /